//Legal Notice: (C)2005 Altera Corporation. All rights reserved.  Your
//use of Altera Corporation's design tools, logic functions and other
//software and tools, and its AMPP partner logic functions, and any
//output files any of the foregoing (including device programming or
//simulation files), and any associated documentation or information are
//expressly subject to the terms and conditions of the Altera Program
//License Subscription Agreement or other applicable license agreement,
//including, without limitation, that your use is for the sole purpose
//of programming logic devices manufactured by Altera and sold by Altera
//or its authorized distributors.  Please refer to the applicable
//agreement for further details.

// synthesis translate_off
`timescale 1ns / 100ps
// synthesis translate_on
module uart_0_log_module (
                           // inputs:
                            clk,
                            data,
                            strobe,
                            valid
                         );

  input            clk;
  input   [  7: 0] data;
  input            strobe;
  input            valid;


//synthesis translate_off
//////////////// SIMULATION-ONLY CONTENTS
   reg [31:0] text_handle; // for $fopen
   initial text_handle = $fopen ("C:/DE2/UP4_NIOS_HOST_MOUSE/nios_0_sim/uart_0_log_module.txt");

   always @(posedge clk) begin
      if (valid && strobe) begin
	 // Send \n (linefeed) instead of \r (^M, Carriage Return)...
         $fwrite (text_handle, "%s", ((data == 8'hd) ? 8'ha : data));
	 // non-standard; poorly documented; required to get real data stream.
	 $fflush (text_handle);
      end
   end // clk


//////////////// END SIMULATION-ONLY CONTENTS

//synthesis translate_on


endmodule


module uart_0_tx (
                   // inputs:
                    baud_divisor,
                    begintransfer,
                    clk,
                    clk_en,
                    do_force_break,
                    reset_n,
                    status_wr_strobe,
                    tx_data,
                    tx_wr_strobe,

                   // outputs:
                    tx_overrun,
                    tx_ready,
                    tx_shift_empty,
                    txd
                 );

  output           tx_overrun;
  output           tx_ready;
  output           tx_shift_empty;
  output           txd;
  input   [  8: 0] baud_divisor;
  input            begintransfer;
  input            clk;
  input            clk_en;
  input            do_force_break;
  input            reset_n;
  input            status_wr_strobe;
  input   [  7: 0] tx_data;
  input            tx_wr_strobe;

  reg              baud_clk_en;
  reg     [  8: 0] baud_rate_counter;
  wire             baud_rate_counter_is_zero;
  reg              do_load_shifter;
  wire             do_shift;
  reg              pre_txd;
  wire             shift_done;
  wire    [  9: 0] tx_load_val;
  reg              tx_overrun;
  reg              tx_ready;
  reg              tx_shift_empty;
  wire             tx_shift_reg_out;
  wire    [  9: 0] tx_shift_register_contents;
  wire             tx_wr_strobe_onset;
  reg              txd;
  wire    [  9: 0] unxshiftxtx_shift_register_contentsxtx_shift_reg_outxx5_in;
  reg     [  9: 0] unxshiftxtx_shift_register_contentsxtx_shift_reg_outxx5_out;
  assign tx_wr_strobe_onset = tx_wr_strobe && begintransfer;
  assign tx_load_val = {{1 {1'b1}},
    tx_data,
    1'b0};

  assign shift_done = ~(|tx_shift_register_contents);
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          do_load_shifter <= 0;
      else if (clk_en)
          do_load_shifter <= (~tx_ready) && shift_done;
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          tx_ready <= 1'b1;
      else if (clk_en)
          if (tx_wr_strobe_onset)
              tx_ready <= 0;
          else if (do_load_shifter)
              tx_ready <= -1;
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          tx_overrun <= 0;
      else if (clk_en)
          if (status_wr_strobe)
              tx_overrun <= 0;
          else if (~tx_ready && tx_wr_strobe_onset)
              tx_overrun <= -1;
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          tx_shift_empty <= 1'b1;
      else if (clk_en)
          tx_shift_empty <= tx_ready && shift_done;
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          baud_rate_counter <= 0;
      else if (clk_en)
          if (baud_rate_counter_is_zero || do_load_shifter)
              baud_rate_counter <= baud_divisor;
          else 
            baud_rate_counter <= baud_rate_counter - 1;
    end


  assign baud_rate_counter_is_zero = baud_rate_counter == 0;
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          baud_clk_en <= 0;
      else if (clk_en)
          baud_clk_en <= baud_rate_counter_is_zero;
    end


  assign do_shift = baud_clk_en  && 
    (~shift_done) && 
    (~do_load_shifter);

  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          pre_txd <= 1;
      else if (~shift_done)
          pre_txd <= tx_shift_reg_out;
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          txd <= 1;
      else if (clk_en)
          txd <= pre_txd & ~do_force_break;
    end


  //_reg, which is an e_register
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          unxshiftxtx_shift_register_contentsxtx_shift_reg_outxx5_out <= 0;
      else if (clk_en)
          unxshiftxtx_shift_register_contentsxtx_shift_reg_outxx5_out <= unxshiftxtx_shift_register_contentsxtx_shift_reg_outxx5_in;
    end


  assign unxshiftxtx_shift_register_contentsxtx_shift_reg_outxx5_in = (do_load_shifter)? tx_load_val :
    (do_shift)? {1'b0,
    unxshiftxtx_shift_register_contentsxtx_shift_reg_outxx5_out[9 : 1]} :
    unxshiftxtx_shift_register_contentsxtx_shift_reg_outxx5_out;

  assign tx_shift_register_contents = unxshiftxtx_shift_register_contentsxtx_shift_reg_outxx5_out;
  assign tx_shift_reg_out = unxshiftxtx_shift_register_contentsxtx_shift_reg_outxx5_out[0];


endmodule


module uart_0_rx_stimulus_source_character_source_rom_module (
                                                               // inputs:
                                                                clk,
                                                                incr_addr,
                                                                reset_n,

                                                               // outputs:
                                                                new_rom,
                                                                q,
                                                                safe
                                                             );

  parameter POLL_RATE = 100;


  output           new_rom;
  output  [  7: 0] q;
  output           safe;
  input            clk;
  input            incr_addr;
  input            reset_n;

  reg     [ 10: 0] address;
  reg              d1_pre;
  reg              d2_pre;
  reg              d3_pre;
  reg              d4_pre;
  reg              d5_pre;
  reg              d6_pre;
  reg              d7_pre;
  reg              d8_pre;
  reg              d9_pre;
  reg     [  7: 0] mem_array [1023: 0];
  reg     [ 31: 0] mutex [  1: 0];
  reg              new_rom;
  reg              pre;
  wire    [  7: 0] q;
  wire             safe;

//synthesis translate_off
//////////////// SIMULATION-ONLY CONTENTS
  assign q = mem_array[address];
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
        begin
          d1_pre <= 0;
          d2_pre <= 0;
          d3_pre <= 0;
          d4_pre <= 0;
          d5_pre <= 0;
          d6_pre <= 0;
          d7_pre <= 0;
          d8_pre <= 0;
          d9_pre <= 0;
          new_rom <= 0;
        end
      else if (1)
        begin
          d1_pre <= pre;
          d2_pre <= d1_pre;
          d3_pre <= d2_pre;
          d4_pre <= d3_pre;
          d5_pre <= d4_pre;
          d6_pre <= d5_pre;
          d7_pre <= d6_pre;
          d8_pre <= d7_pre;
          d9_pre <= d8_pre;
          new_rom <= d9_pre;
        end
    end


   reg        safe_delay;
   reg [31:0] poll_count;
   reg [31:0] mutex_handle;
   wire       interactive = 1'b0 ; // '
   assign     safe = (address < mutex[1]);

   initial poll_count = POLL_RATE;

   always @(posedge clk or negedge reset_n) begin
      if (reset_n !== 1) begin
         safe_delay <= 0;
      end else begin
         safe_delay <= safe;
      end
   end // safe_delay

   always @(posedge clk or negedge reset_n) begin
      if (reset_n !== 1) begin  // dont worry about null _stream.dat file
         address <= 0;
         mem_array[0] <= 0;
         mutex[0] <= 0;
         mutex[1] <= 0;
         pre <= 0;
      end else begin            // deal with the non-reset case
         pre <= 0;
         if (incr_addr && safe) address <= address + 1;
         if (mutex[0] && !safe && safe_delay) begin
            // and blast the mutex after falling edge of safe if interactive
            if (interactive) begin
               mutex_handle = $fopen ("C:/DE2/UP4_NIOS_HOST_MOUSE/nios_0_sim/uart_0_input_data_mutex.dat");
               $fdisplay (mutex_handle, "0");
               $fclose (mutex_handle);
               // $display ($stime, "\t%m:\n\t\tMutex cleared!");
            end else begin
               // sleep until next reset, do not bash mutex.
               wait (!reset_n);
            end
         end // OK to bash mutex.
         if (poll_count < POLL_RATE) begin // wait
            poll_count = poll_count + 1;
         end else begin         // do the interesting stuff.
            poll_count = 0;
            $readmemh ("C:/DE2/UP4_NIOS_HOST_MOUSE/nios_0_sim/uart_0_input_data_mutex.dat", mutex);
            if (mutex[0] && !safe) begin
            // read stream into mem_array after current characters are gone!
               // save mutex[0] value to compare to address (generates 'safe')
               mutex[1] <= mutex[0];
               // $display ($stime, "\t%m:\n\t\tMutex hit: Trying to read %d bytes...", mutex[0]);
               $readmemh("C:/DE2/UP4_NIOS_HOST_MOUSE/nios_0_sim/uart_0_input_data_stream.dat", mem_array);
               // bash address and send pulse outside to send the char:
               address <= 0;
               pre <= -1;
            end // else mutex miss...
         end // poll_count
      end // reset
   end // posedge clk


//////////////// END SIMULATION-ONLY CONTENTS

//synthesis translate_on


endmodule


module uart_0_rx_stimulus_source (
                                   // inputs:
                                    baud_divisor,
                                    clk,
                                    clk_en,
                                    reset_n,
                                    rx_char_ready,
                                    rxd,

                                   // outputs:
                                    source_rxd
                                 );

  output           source_rxd;
  input   [  8: 0] baud_divisor;
  input            clk;
  input            clk_en;
  input            reset_n;
  input            rx_char_ready;
  input            rxd;

  reg     [  7: 0] d1_stim_data;
  reg              delayed_unxrx_char_readyxx0;
  wire             do_send_stim_data;
  wire             new_rom_pulse;
  wire             pickup_pulse;
  wire             safe;
  wire             source_rxd;
  wire    [  7: 0] stim_data;
  wire             unused_empty;
  wire             unused_overrun;
  wire             unused_ready;

//synthesis translate_off
//////////////// SIMULATION-ONLY CONTENTS
  //stimulus_transmitter, which is an e_instance
  uart_0_tx stimulus_transmitter
    (
      .baud_divisor     (baud_divisor),
      .begintransfer    (do_send_stim_data),
      .clk              (clk),
      .clk_en           (clk_en),
      .do_force_break   (1'b0),
      .reset_n          (reset_n),
      .status_wr_strobe (1'b0),
      .tx_data          (d1_stim_data),
      .tx_overrun       (unused_overrun),
      .tx_ready         (unused_ready),
      .tx_shift_empty   (unused_empty),
      .tx_wr_strobe     (1'b1),
      .txd              (source_rxd)
    );

  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          d1_stim_data <= 0;
      else if (do_send_stim_data)
          d1_stim_data <= stim_data;
    end


  //uart_0_rx_stimulus_source_character_source_rom, which is an e_drom
  uart_0_rx_stimulus_source_character_source_rom_module uart_0_rx_stimulus_source_character_source_rom
    (
      .clk       (clk),
      .incr_addr (do_send_stim_data),
      .new_rom   (new_rom_pulse),
      .q         (stim_data),
      .reset_n   (reset_n),
      .safe      (safe)
    );

  //delayed_unxrx_char_readyxx0, which is an e_register
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          delayed_unxrx_char_readyxx0 <= 0;
      else if (clk_en)
          delayed_unxrx_char_readyxx0 <= rx_char_ready;
    end


  assign pickup_pulse = ~(rx_char_ready) &  (delayed_unxrx_char_readyxx0);
  assign do_send_stim_data = (pickup_pulse || new_rom_pulse) && safe;

//////////////// END SIMULATION-ONLY CONTENTS

//synthesis translate_on
//synthesis read_comments_as_HDL on
//  assign source_rxd = rxd;
//synthesis read_comments_as_HDL off


endmodule


module uart_0_rx (
                   // inputs:
                    baud_divisor,
                    begintransfer,
                    clk,
                    clk_en,
                    reset_n,
                    rx_rd_strobe,
                    rxd,
                    status_wr_strobe,

                   // outputs:
                    break_detect,
                    framing_error,
                    parity_error,
                    rx_char_ready,
                    rx_data,
                    rx_overrun
                 );

  output           break_detect;
  output           framing_error;
  output           parity_error;
  output           rx_char_ready;
  output  [  7: 0] rx_data;
  output           rx_overrun;
  input   [  8: 0] baud_divisor;
  input            begintransfer;
  input            clk;
  input            clk_en;
  input            reset_n;
  input            rx_rd_strobe;
  input            rxd;
  input            status_wr_strobe;

  reg              baud_clk_en;
  wire    [  8: 0] baud_load_value;
  reg     [  8: 0] baud_rate_counter;
  wire             baud_rate_counter_is_zero;
  reg              break_detect;
  reg              d1_source_rxd;
  reg              delayed_unxrx_in_processxx3;
  reg              delayed_unxsync_rxdxx1;
  reg              delayed_unxsync_rxdxx2;
  reg              do_start_rx;
  reg              framing_error;
  wire             got_new_char;
  wire    [  7: 0] half_bit_cell_divisor;
  wire             is_break;
  wire             is_framing_error;
  wire             parity_error;
  wire    [  7: 0] raw_data_in;
  reg              rx_char_ready;
  reg     [  7: 0] rx_data;
  wire             rx_in_process;
  reg              rx_overrun;
  wire             rx_rd_strobe_onset;
  wire             rxd_edge;
  wire             rxd_falling;
  wire    [  9: 0] rxd_shift_reg;
  wire             sample_enable;
  wire             shift_reg_start_bit_n;
  wire             source_rxd;
  wire             stop_bit;
  reg              sync_rxd;
  wire             unused_start_bit;
  wire    [  9: 0] unxshiftxrxd_shift_regxshift_reg_start_bit_nxx6_in;
  reg     [  9: 0] unxshiftxrxd_shift_regxshift_reg_start_bit_nxx6_out;
  uart_0_rx_stimulus_source the_uart_0_rx_stimulus_source
    (
      .baud_divisor  (baud_divisor),
      .clk           (clk),
      .clk_en        (clk_en),
      .reset_n       (reset_n),
      .rx_char_ready (rx_char_ready),
      .rxd           (rxd),
      .source_rxd    (source_rxd)
    );

  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
        begin
          d1_source_rxd <= 0;
          sync_rxd <= 0;
        end
      else if (clk_en)
        begin
          d1_source_rxd <= source_rxd;
          sync_rxd <= d1_source_rxd;
        end
    end


  //delayed_unxsync_rxdxx1, which is an e_register
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          delayed_unxsync_rxdxx1 <= 0;
      else if (clk_en)
          delayed_unxsync_rxdxx1 <= sync_rxd;
    end


  assign rxd_falling = ~(sync_rxd) &  (delayed_unxsync_rxdxx1);
  //delayed_unxsync_rxdxx2, which is an e_register
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          delayed_unxsync_rxdxx2 <= 0;
      else if (clk_en)
          delayed_unxsync_rxdxx2 <= sync_rxd;
    end


  assign rxd_edge = (sync_rxd) ^  (delayed_unxsync_rxdxx2);
  assign rx_rd_strobe_onset = rx_rd_strobe && begintransfer;
  assign half_bit_cell_divisor = baud_divisor[8 : 1];
  assign baud_load_value = (rxd_edge)? half_bit_cell_divisor :
    baud_divisor;

  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          baud_rate_counter <= 0;
      else if (clk_en)
          if (baud_rate_counter_is_zero || rxd_edge)
              baud_rate_counter <= baud_load_value;
          else 
            baud_rate_counter <= baud_rate_counter - 1;
    end


  assign baud_rate_counter_is_zero = baud_rate_counter == 0;
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          baud_clk_en <= 0;
      else if (clk_en)
          if (rxd_edge)
              baud_clk_en <= 0;
          else 
            baud_clk_en <= baud_rate_counter_is_zero;
    end


  assign sample_enable = baud_clk_en && rx_in_process;
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          do_start_rx <= 0;
      else if (clk_en)
          if (~rx_in_process && rxd_falling)
              do_start_rx <= 1;
          else 
            do_start_rx <= 0;
    end


  assign rx_in_process = shift_reg_start_bit_n;
  assign {stop_bit,
raw_data_in,
unused_start_bit} = rxd_shift_reg;
  assign is_break = ~(|rxd_shift_reg);
  assign is_framing_error = ~stop_bit && ~is_break;
  //delayed_unxrx_in_processxx3, which is an e_register
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          delayed_unxrx_in_processxx3 <= 0;
      else if (clk_en)
          delayed_unxrx_in_processxx3 <= rx_in_process;
    end


  assign got_new_char = ~(rx_in_process) &  (delayed_unxrx_in_processxx3);
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          rx_data <= 0;
      else if (got_new_char)
          rx_data <= raw_data_in;
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          framing_error <= 0;
      else if (clk_en)
          if (status_wr_strobe)
              framing_error <= 0;
          else if (got_new_char && is_framing_error)
              framing_error <= -1;
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          break_detect <= 0;
      else if (clk_en)
          if (status_wr_strobe)
              break_detect <= 0;
          else if (got_new_char && is_break)
              break_detect <= -1;
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          rx_overrun <= 0;
      else if (clk_en)
          if (status_wr_strobe)
              rx_overrun <= 0;
          else if (got_new_char && rx_char_ready)
              rx_overrun <= -1;
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          rx_char_ready <= 0;
      else if (clk_en)
          if (rx_rd_strobe_onset)
              rx_char_ready <= 0;
          else if (got_new_char)
              rx_char_ready <= -1;
    end


  assign parity_error = 0;
  //_reg, which is an e_register
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          unxshiftxrxd_shift_regxshift_reg_start_bit_nxx6_out <= 0;
      else if (clk_en)
          unxshiftxrxd_shift_regxshift_reg_start_bit_nxx6_out <= unxshiftxrxd_shift_regxshift_reg_start_bit_nxx6_in;
    end


  assign unxshiftxrxd_shift_regxshift_reg_start_bit_nxx6_in = (do_start_rx)? {10{1'b1}} :
    (sample_enable)? {sync_rxd,
    unxshiftxrxd_shift_regxshift_reg_start_bit_nxx6_out[9 : 1]} :
    unxshiftxrxd_shift_regxshift_reg_start_bit_nxx6_out;

  assign rxd_shift_reg = unxshiftxrxd_shift_regxshift_reg_start_bit_nxx6_out;
  assign shift_reg_start_bit_n = unxshiftxrxd_shift_regxshift_reg_start_bit_nxx6_out[0];


endmodule


module uart_0_regs (
                     // inputs:
                      address,
                      break_detect,
                      chipselect,
                      clk,
                      clk_en,
                      framing_error,
                      parity_error,
                      read_n,
                      reset_n,
                      rx_char_ready,
                      rx_data,
                      rx_overrun,
                      tx_overrun,
                      tx_ready,
                      tx_shift_empty,
                      write_n,
                      writedata,

                     // outputs:
                      baud_divisor,
                      dataavailable,
                      do_force_break,
                      irq,
                      readdata,
                      readyfordata,
                      rx_rd_strobe,
                      status_wr_strobe,
                      tx_data,
                      tx_wr_strobe
                   );

  output  [  8: 0] baud_divisor;
  output           dataavailable;
  output           do_force_break;
  output           irq;
  output  [ 15: 0] readdata;
  output           readyfordata;
  output           rx_rd_strobe;
  output           status_wr_strobe;
  output  [  7: 0] tx_data;
  output           tx_wr_strobe;
  input   [  2: 0] address;
  input            break_detect;
  input            chipselect;
  input            clk;
  input            clk_en;
  input            framing_error;
  input            parity_error;
  input            read_n;
  input            reset_n;
  input            rx_char_ready;
  input   [  7: 0] rx_data;
  input            rx_overrun;
  input            tx_overrun;
  input            tx_ready;
  input            tx_shift_empty;
  input            write_n;
  input   [ 15: 0] writedata;

  wire             any_error;
  wire    [  8: 0] baud_divisor;
  reg     [  9: 0] control_reg;
  wire             control_wr_strobe;
  wire             cts_status_bit;
  reg              d1_rx_char_ready;
  reg              d1_tx_ready;
  wire             dataavailable;
  wire             dcts_status_bit;
  reg              delayed_unxtx_readyxx4;
  wire    [  8: 0] divisor_constant;
  wire             do_force_break;
  wire             do_write_char;
  wire             eop_status_bit;
  wire             ie_any_error;
  wire             ie_break_detect;
  wire             ie_framing_error;
  wire             ie_parity_error;
  wire             ie_rx_char_ready;
  wire             ie_rx_overrun;
  wire             ie_tx_overrun;
  wire             ie_tx_ready;
  wire             ie_tx_shift_empty;
  reg              irq;
  wire             qualified_irq;
  reg     [ 15: 0] readdata;
  wire             readyfordata;
  wire             rx_rd_strobe;
  wire    [ 15: 0] selected_read_data;
  wire    [ 12: 0] status_reg;
  wire             status_wr_strobe;
  reg     [  7: 0] tx_data;
  wire             tx_wr_strobe;
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          readdata <= 0;
      else if (clk_en)
          readdata <= selected_read_data;
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          irq <= 0;
      else if (clk_en)
          irq <= qualified_irq;
    end


  assign rx_rd_strobe = chipselect && ~read_n  && (address == 3'd0);
  assign tx_wr_strobe = chipselect && ~write_n && (address == 3'd1);
  assign status_wr_strobe = chipselect && ~write_n && (address == 3'd2);
  assign control_wr_strobe = chipselect && ~write_n && (address == 3'd3);
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          tx_data <= 0;
      else if (tx_wr_strobe)
          tx_data <= writedata[7 : 0];
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          control_reg <= 0;
      else if (control_wr_strobe)
          control_reg <= writedata[9 : 0];
    end


  assign baud_divisor = divisor_constant;
  assign cts_status_bit = 0;
  assign dcts_status_bit = 0;
  assign {do_force_break,
ie_any_error,
ie_rx_char_ready,
ie_tx_ready,
ie_tx_shift_empty,
ie_tx_overrun,
ie_rx_overrun,
ie_break_detect,
ie_framing_error,
ie_parity_error} = control_reg;
  assign any_error = tx_overrun ||
    rx_overrun ||
    parity_error ||
    framing_error ||
    break_detect;

  assign status_reg = {eop_status_bit,
    cts_status_bit,
    dcts_status_bit,
    1'b0,
    any_error,
    rx_char_ready,
    tx_ready,
    tx_shift_empty,
    tx_overrun,
    rx_overrun,
    break_detect,
    framing_error,
    parity_error};

  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          d1_rx_char_ready <= 0;
      else if (clk_en)
          d1_rx_char_ready <= rx_char_ready;
    end


  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          d1_tx_ready <= 0;
      else if (clk_en)
          d1_tx_ready <= tx_ready;
    end


  assign dataavailable = d1_rx_char_ready;
  assign readyfordata = d1_tx_ready;
  assign eop_status_bit = 1'b0;
  assign selected_read_data = ({16 {(address == 3'd0)}} & rx_data) |
    ({16 {(address == 3'd1)}} & tx_data) |
    ({16 {(address == 3'd2)}} & status_reg) |
    ({16 {(address == 3'd3)}} & control_reg);

  assign qualified_irq = (ie_any_error      && any_error      ) ||
    (ie_tx_shift_empty && tx_shift_empty ) ||
    (ie_tx_overrun     && tx_overrun     ) ||
    (ie_rx_overrun     && rx_overrun     ) ||
    (ie_break_detect   && break_detect   ) ||
    (ie_framing_error  && framing_error  ) ||
    (ie_parity_error   && parity_error   ) ||
    (ie_rx_char_ready  && rx_char_ready  ) ||
    (ie_tx_ready       && tx_ready       );


//synthesis translate_off
//////////////// SIMULATION-ONLY CONTENTS
  //delayed_unxtx_readyxx4, which is an e_register
  always @(posedge clk or negedge reset_n)
    begin
      if (reset_n == 0)
          delayed_unxtx_readyxx4 <= 0;
      else if (clk_en)
          delayed_unxtx_readyxx4 <= tx_ready;
    end


  assign do_write_char = (tx_ready) & ~(delayed_unxtx_readyxx4);
  always @(posedge clk)
    begin
      if (do_write_char)
          $write("%c", tx_data);
    end


  assign divisor_constant = 4;

//////////////// END SIMULATION-ONLY CONTENTS

//synthesis translate_on
//synthesis read_comments_as_HDL on
//  assign divisor_constant = 434;
//synthesis read_comments_as_HDL off


endmodule


module uart_0 (
                // inputs:
                 address,
                 begintransfer,
                 chipselect,
                 clk,
                 read_n,
                 reset_n,
                 rxd,
                 write_n,
                 writedata,

                // outputs:
                 dataavailable,
                 irq,
                 readdata,
                 readyfordata,
                 txd
              );

  output           dataavailable;
  output           irq;
  output  [ 15: 0] readdata;
  output           readyfordata;
  output           txd;
  input   [  2: 0] address;
  input            begintransfer;
  input            chipselect;
  input            clk;
  input            read_n;
  input            reset_n;
  input            rxd;
  input            write_n;
  input   [ 15: 0] writedata;

  wire    [  8: 0] baud_divisor;
  wire             break_detect;
  wire             clk_en;
  wire             dataavailable;
  wire             do_force_break;
  wire             framing_error;
  wire             irq;
  wire             parity_error;
  wire    [ 15: 0] readdata;
  wire             readyfordata;
  wire             rx_char_ready;
  wire    [  7: 0] rx_data;
  wire             rx_overrun;
  wire             rx_rd_strobe;
  wire             status_wr_strobe;
  wire    [  7: 0] tx_data;
  wire             tx_overrun;
  wire             tx_ready;
  wire             tx_shift_empty;
  wire             tx_wr_strobe;
  wire             txd;
  assign clk_en = 1;
  uart_0_tx the_uart_0_tx
    (
      .baud_divisor     (baud_divisor),
      .begintransfer    (begintransfer),
      .clk              (clk),
      .clk_en           (clk_en),
      .do_force_break   (do_force_break),
      .reset_n          (reset_n),
      .status_wr_strobe (status_wr_strobe),
      .tx_data          (tx_data),
      .tx_overrun       (tx_overrun),
      .tx_ready         (tx_ready),
      .tx_shift_empty   (tx_shift_empty),
      .tx_wr_strobe     (tx_wr_strobe),
      .txd              (txd)
    );

  uart_0_rx the_uart_0_rx
    (
      .baud_divisor     (baud_divisor),
      .begintransfer    (begintransfer),
      .break_detect     (break_detect),
      .clk              (clk),
      .clk_en           (clk_en),
      .framing_error    (framing_error),
      .parity_error     (parity_error),
      .reset_n          (reset_n),
      .rx_char_ready    (rx_char_ready),
      .rx_data          (rx_data),
      .rx_overrun       (rx_overrun),
      .rx_rd_strobe     (rx_rd_strobe),
      .rxd              (rxd),
      .status_wr_strobe (status_wr_strobe)
    );

  uart_0_regs the_uart_0_regs
    (
      .address          (address),
      .baud_divisor     (baud_divisor),
      .break_detect     (break_detect),
      .chipselect       (chipselect),
      .clk              (clk),
      .clk_en           (clk_en),
      .dataavailable    (dataavailable),
      .do_force_break   (do_force_break),
      .framing_error    (framing_error),
      .irq              (irq),
      .parity_error     (parity_error),
      .read_n           (read_n),
      .readdata         (readdata),
      .readyfordata     (readyfordata),
      .reset_n          (reset_n),
      .rx_char_ready    (rx_char_ready),
      .rx_data          (rx_data),
      .rx_overrun       (rx_overrun),
      .rx_rd_strobe     (rx_rd_strobe),
      .status_wr_strobe (status_wr_strobe),
      .tx_data          (tx_data),
      .tx_overrun       (tx_overrun),
      .tx_ready         (tx_ready),
      .tx_shift_empty   (tx_shift_empty),
      .tx_wr_strobe     (tx_wr_strobe),
      .write_n          (write_n),
      .writedata        (writedata)
    );

  //s1, which is an e_avalon_slave

//synthesis translate_off
//////////////// SIMULATION-ONLY CONTENTS
  //uart_0_log, which is an e_log
  uart_0_log_module uart_0_log
    (
      .clk    (clk),
      .data   (tx_data),
      .strobe (tx_wr_strobe),
      .valid  (~tx_ready)
    );


//////////////// END SIMULATION-ONLY CONTENTS

//synthesis translate_on


endmodule